Wrist-to-Floor Fitting · +/- Shaft Length · Upright vs. Flat Lie

Wrist-to-floor & lie.
Square the sole at impact.

Height alone lies about arm length—and 2° of wrong iron lie angle points your clubface 7 yards offline before you even swing. Use Club Carry (clubcarry.com) to combine Height + Wrist-to-Floor + Divot feedback into exact iron length and lie specs.

Standard WTF window
33.5"–35.5" (Std len)
1° wrong iron lie
~3.5 yd push or pull
+0.50" shaft length
+3 swingweight pts
Quick Verdict · Updated Nov 2026

Measure Wrist-to-Floor (WTF) in golf shoes: 33.5"–35.5" fits Standard length (37.00" 7-iron), stepping +0.25" to +0.50" per ~1.5" higher WTF (and -0.25" to -0.50" below 33"). Every 1° of toe-down (too flat) tilts iron aim ~3.5 yd right (adjust Upright); every 1° of heel-down (too upright) tilts aim ~3.5 yd left (adjust Flat).

01 · Static posture & divot check
6'2" (74 in)
37.0 in (94.0 cm)
04 · Dynamic Turf Divot / Start-Line Pattern
Sole-Turf Plane & Iron Spec +0.50" Length · 2° Upright
6'2" Height · 37.0" WTF · Even Divot
Iron Length Spec +0.50" 37.50" finished 7-iron
Dynamic Lie Spec 2° Upright ~64.5° 7-iron (vs. 62.5° std)
Aim Error Saved ~7 yd Build note: +3.0 SW pts

01

WRIST-TO-FLOOR BENCHMARKS

Wrist-to-floor iron length & starting lie chart (28"–40").

Click any Wrist-to-Floor row below to load its baseline shaft length and lie spec above:

Baseline iron shaft length adjustment and starting lie angle by Wrist-to-Floor measurement in golf shoes
Wrist-to-Floor Iron Length 7-Iron Cut Starting Lie Load
29.0"–31.5" (74–80 cm) -0.50" 36.50" 1.5°–2° Flat
32.0"–33.0" (81–84 cm) -0.25" 36.75" 1° Flat
33.5"–35.5" (85–90 cm) Standard 37.00" Standard (0°)
36.0"–37.5" (91–95 cm) +0.50" 37.50" 1.5°–2° Upright
38.0"–40.0" (97–102 cm) +1.00" 38.00" 3° Upright
02

DYNAMIC VERIFICATION

Verify your dynamic lie in 3 swings with the Dry-Erase Marker Test.

Never bend forged irons off a carpet lie board (which can trick clubheads into skidding)—use the Tour-proven vertical dry-erase line on a range ball:

  1. Draw a straight vertical line on the back of a golf ball with a dry-erase marker and place that line pointing straight vertical (12-to-6 o’clock) facing your iron clubface.
  2. Hit a normal 7-iron shot and check the ink line transferred onto your grooves!
  3. Read the angle: Perfectly vertical (12:00) = Exact Flush Lie; tilted toward the toe = Too Flat (bend Upright); tilted toward the hosel = Too Upright (bend Flat).
03

LENGTH & LIE FAQ

Common club length & lie angle questions.

Should I lengthen my driver by the same +0.50" or +1.00" as my irons?

Rarely! Stock retail drivers already ship at 45.50" to 45.75"—which is a full inch longer than PGA Tour average (~44.5"–44.75"). Even 6'3" golfers usually hit more center-face drives at stock 45.25"–45.50" length (see smash factor center-strike math).

Can cast stainless-steel irons have their lie angles bent?

Forged carbon-steel irons bend smoothly up to ±3°–4° in any repair shop; investment-cast 17-4 / 431 stainless irons can usually be adjusted ±1.5°–2° by an experienced builder (or ordered pre-cast in your color/lie code).

Should scoring wedges be 1° flatter than my 7-iron?

Many Tour fitters set 54°–60° wedges 0.5° to 1° flatter than full-swing irons because partial pitch shots produce less downward shaft droop—preventing tugged left wedge shots (see wedge gapping matrix).